On KD Machinery’s listings the ShopSabre PRO is a CNC router in three sizes, the PRO404, PRO408 and PRO510, and the digits read as the nominal sheet size in feet. KD Machinery buys and sells used PROs built from 2018 to 2025.
No used ShopSabre PRO CNC routers are listed for sale right now. Ask KD Machinery to find one.
Read the three digits as the nominal sheet size in feet. The PRO408 is the 4 by 8 foot machine, common on KD Machinery’s record. The PRO510 is the 5 by 10, and the PRO404 the small 4 by 4. The table sizes on the listings run a little larger than the sheet: a PRO408 is usually listed with a 60 by 96 inch table and a PRO510 with a 60 by 120 inch table. If you cut full 5 by 10 sheets, only the PRO510 will take one in a single setup.
Most PROs KD Machinery has listed carry a 24,000 rpm HSD spindle with an automatic tool changer, usually 10 hp and sometimes 5 hp. Tool changers on the record run from 5 to 12 positions. The 18,000 rpm machines have a smaller 4 hp spindle and no tool changer listed, and at least one is listed as a manual tool change. A manual-change machine costs less to buy and more in operator time, so price the two separately.
The PRO listings that name the control give WinCNC on a ShopSabre computer, and many PROs on the record were sold with Vectric VCarve Pro for design and toolpaths. Several listings note that the software may need re-registration, with a fee, for a new owner, so ask what transfers with the machine. Check the power, too: KD Machinery has listed PROs on single-phase and on three-phase supplies, and the shop’s service has to match.
Run the spindle up through its range and listen for bearing noise. Jog the gantry the full length of the table and look at the rails and racks for wear and dust packing. Test every vacuum zone with a sheet on the table; four zones are common. Many listings include a tool measure switch and a material height touch pad; if yours does, check both work.
KD Machinery also lists the ShopSabre IS and RC lines, which are separate machines with their own sizes. To compare a PRO with other makes, browse used CNC routers or the larger used Multicam CNC routers.
We have handled 10 ShopSabre PRO machines, spanning build years 2018 to 2025. That is our own record, not a catalog listing.
The used ShopSabre PRO market is dominated by the PRO408, which accounts for 7 of the 10 machines we have handled. If you are shopping an PRO, that is most likely what you are looking at.
| Z-Axis Travel | 16" (1 of 10), 14" (1 of 10) |
|---|---|
| Table Length | 96" (7 of 10), 120" (2 of 10), 48" (1 of 10) |
| Table Width | 60" (9 of 10), 48" (1 of 10) |
| Spindle Speed | 24,000 RPM (5 of 10), 18,000 RPM VFD (1 of 10) |
| Spindle Motor | 10 HP (5 of 10), 5 HP (1 of 10), 4 HP (1 of 10) |
| Control | Shopsabre WINCNC Industrial Controller Hardware & Softward (1 of 10), ShopSabre Computer System - Full Size Desktop System with Solid State Hard Drive/8GB Memory/19" Flat Screen Monitor/Keyboard/Mouse (1 of 10), Shopsabre WINCNC Industrial Controller Hardware & Software (1 of 10), and 7 others |
| Power Requirement | Single Phase (Router & Pump) (1 of 10), Single & 3-Phase (1 of 10), 480v - 3ph (1 of 10), and 2 others |
Across 33 ShopSabre PRO machines we have listed with a published price, the middle half ran from $29,500 to $43,500, with a median of $36,850. A quarter were listed below that band and a quarter above it. These are the prices we asked, not what any machine changed hands for — condition, hours, tooling and control generation move a machine within it. Ask us where a specific one sits. Asking prices as of November 2026.
The size. Read the digits as the nominal sheet size in feet: the PRO408 is the 4 by 8 foot router and the PRO510 the 5 by 10. On KD Machinery's listings a PRO408 usually has a 60 by 96 inch table and a PRO510 a 60 by 120 inch table.
Ask before you buy. Several ShopSabre listings on KD Machinery's record note that the design software, often Vectric VCarve Pro, may need re-registration with a fee for a new owner. The PRO listings that name the control give WinCNC on a ShopSabre computer, so confirm the computer is included.
Across 33 ShopSabre PRO machines KD Machinery has listed with a published price, the middle half ran from $29,500 to $43,500, with a median of $36,850. A quarter were listed below that band and a quarter above it. These are the prices we asked, not what any machine changed hands for — condition, hours, tooling and control generation move a machine within it. Asking prices as of November 2026.
Of the 10 ShopSabre PRO machines KD Machinery has handled, the most common variants are PRO408 (7), PRO510 (2), PRO404 (1). That is our own record of what has actually come through, not a catalog of everything the manufacturer built.
KD runs lien searches on every transaction so that our buyers can have peace of mind that they are purchasing an asset that does not have any active liens on it. We take this very seriously and are willing to pass up a deal if the seller won't cooperate on getting active liens cleared.
KD Machinery has bought and sold 10 ShopSabre PRO machines built between 2018 and 2025.
KD Machinery buys the ShopSabre PRO and other used machines outright. Tell us what you have and how to reach you, and we will get back to you. The make and model are enough to start.
How it works and what we buy: Sell your machines.
KD Machinery buys single machines, and whole shops and plants, outright. Auction-based plant liquidations and formal USPAP appraisals are handled by KD Auctions: see plant liquidation by auction and USPAP appraisals.
